a级毛片无码久久精品免费_柠檬福利第一导航在线_广东少妇大战黑人34厘米视频_色噜噜狠狠综曰曰曰

Welcome to Jinan Jinli Hydraulic Machinery Co., Ltd! Our company is insured by an insurance company!                              TEL:0531-84233822   TEL:13954115865   中文版

contact us

聯(lián)系我們

TEL:0531-84233822

TEL:15550068833/13954115865

E-mail:jinliyeya@126.com

Address: Haichuang Industrial Park, Huanghe Street, Jiyang District, Jinan City

Company News

Faults and solutions of hydraulic lifting platform support system

Source: Time:2020-01-17 09:02:33 views:

Faults and solutions of hydraulic lifting platform support system

In the previous chapter, the company's engineers introduced the support system of the hydraulic lifting platform. Today, we will explain some possible faults of the hydraulic support legs and corresponding solutions. Malfunctions and Solutions of Leg Mechanical Components Repair of Worn Frog Legs The most easily worn part of the frog style leg (a basic type of component failure) is the guide groove on the movable leg. If the wear on its working surface reaches 1.5mm, it should be replaced; Otherwise, when retracting the legs, there will be collision between the movable legs and the fixed legs, which can easily lead to accidents. At this point, it is necessary to weld repair the working surface of the guide groove. When repairing the support system of the elevator, first remove the movable support legs, measure the size of the guide groove, and determine the thickness of the welding repair. When repairing welding, use screws and nuts to install the rectangular copper pad as shown, place the copper tube on the screw, repair one section, and then move the repair welding to the next section until the welding is completed. For convenience, the welding rod can also be bent moderately. But it should be noted that the welding repair position must be on the lower surface of the guide groove in Figure 1. This will not affect the stroke of the piston rod of the hydraulic cylinder and the relative angle between the fixed and movable legs when the legs are loaded. After welding, use a standard shaft as a reference for shaping, and pay attention to repairing both sides of the groove with the same shaft at the same time. If the outer diameter wear of the rolling sleeve exceeds 1mm, it should be replaced; Otherwise, it is easy to be crushed during the operation of the hydraulic lifting platform, causing changes in the stress condition of the support legs and posing a hidden danger to safety production. Repair of wear on the upper and lower surfaces of H-shaped leg horizontal beams In the case of heavy load on the crane, the lifted object is located directly behind the vehicle, higher than the support legs. At this time, when looking at the support legs from the rear of the car, if there is a crawling phenomenon when the horizontal distance is greater than the thickness of the metal plate on the vehicle body, or when the support legs stretch and retract (extension and retraction metaphorically refer to flexibility within a certain limit), the support legs must be removed for inspection. If there are deep grooves or serious damage on the plate surface, the support legs should be replaced with new ones or the worn parts should be welded. The cost of welding repair legs is relatively low and suitable for use. Malfunctions and Maintenance of Leg Hydraulic System According to the hydraulic schematic of the frog leg, the bidirectional hydraulic lock is installed at the upper end of the front leg cylinder, so the tightness of the right angle fixing bolts (dogbolt) on it must be consistent, otherwise it will cause damage to the sealing ring and oil leakage. Its function is to prevent the legs from retracting on their own during elevator operation; Prevent the support legs from automatically falling during the operation or parking of the crane. In the hydraulic system of H-shaped legs, there is no diversion valve but a rotary valve. The legs can move independently and have good adaptability to the ground, but the situation of failure is similar to that of frog legs. Common faults in hydraulic systems for supporting legs: Oil leakage in the oil circuit The reason is that the joint is loose, and the location should be searched and tightened; The seal is damaged and should be replaced; The pipeline has cracks and should be replaced or welded. Failure of leg extension and retraction The bidirectional hydraulic lock is malfunctioning, and the plunger inside the lock is stuck and cannot move. It needs to be disassembled, cleaned, installed, and adjusted; The plunger wear (a basic type of component failure) is severe and a new hydraulic lock should be replaced. The support legs automatically retract during lifting There are two reasons: firstly, the one-way valve in the bidirectional hydraulic lock has poor sealing, and should be removed for maintenance, cleaned, installed, and adjusted. The second issue is internal leakage in the hydraulic cylinder, which requires the removal and inspection of the seals on the piston. After replacing the seals with new ones, they can be reinstalled {16}

{1}

{2}

{3}

{4}

{5}

{6}

{7}

{8}

{9}

{10}

{11}

{12}

{13}

{14}

{15}

????

{16}

Links

91精品无码国产一区二区三区 | 亚洲精品国产精品国自产观看浪潮 | 日韩亚洲中文一区 | 久久精品日韩中文字幕亚洲一区 | 农村午夜理伦三级 | 丰满熟女自慰在线观看 | 免费看的黄色视频网站 | 成人午夜视频综合 | 中文字幕在线观看免费视频 | 国产农村妇女无套内谢视频 | 国产精品久久精品 | 日本高清不卡中文字幕 | 91久久人澡人妻人人做人精品 | 国产AV一区二区三区精品 | 国产91黄色电影在线播放 | 99影院精品午夜无码蜜桃 | 欧美xxxxx经典| 午夜成人性做爰A片4399 | 精品国产伦一区二区三区观看体验 | 国产在线观看免费视频 | 国产精品久久久久久久免费人妻 | 无码秘 蜜桃一区二区三区 久久久久女人精品毛片九一 | 亚洲无码人妻一期两期3期4期 | 成人av影院免费在看 | 777yyy午夜精品无码福利 | 97精品无人区乱码在线观看 | 麻豆电影传媒二区 | 中文亚州日韩欧美 | 17c蘑菇国产精品一区二区 | 无码人妻精品一区二区蜜桃色 | 搡BBB,搡BBBB,搡BBBB | 无套内射 成人片 | 国产三级国产精品国产桃花 | 国产三级一区二区三区 | 日本无码www在线观看 | 免费看A片AAA片三黄白浆 | 一级a爱做片在线观看免费网站 | 亚洲婷五月天第二页 | 国产熟女成人精品视频 | 91精品无码少妇a 6 2v蜜桃 | 国产一级毛片精品A片在线美传媒 |